Where results make sense

About us   |   Why use us?   |   Reviews   |   PR   |   Contact us

Boeing CH-47D Chinook - The Rotor Blade. Blade pitch changes are accomplished by three pitch-varying links connected from the rotating ring of the swashplate to the pitch-varying housing on each rotor blade. A direct-action shock absorber is attached to the blade and to the pitch-varying housing. The blade chord (width) is 32 inches, and the shape of the airfoil is asymmetrical (the upper and lower surfaces are of different shape). www.chinook-helicopter.com /standards/areas/blade.html   (0 words)

The Controllable-Pitch Propeller Changing the angle of incidence (pitch) from the hub to the tip to correspond with the speed produces uniform lift throughout the length of the blade. If the propeller blade was designed with the same angle of incidence throughout its entire length, it would be extremely inefficient because as airspeed increases in flight, the portion near the hub would have a negative angle of attack while the blade tip would be stalled. Pitch is proportional to the blade angle which is the angle between the chord line of the blade and the propeller’s plane of rotation. oldbeacon.com /beacon/controllable-pitch_propeller.htm   (0 words)

Computerized Prop Reconditioning ~ Marine Propeller, sales and service, marine boat propellers, shafting and drive ... The blue bars show the average pitch of each blade and fall in the "pass area" for a class "I" propeller. This shows the actual pitch of the blade at different radii and locations on each blade, also color coded: red for high pitch blue for low and fl for acceptable. For mean pitch of the propeller, angular deviation (blade spacing) and axial position (track) the prop passes for "S" class. www.properpitch.com /cpr.asp   (434 words)

HeliTown.COM/RC Helicopter Pitch Range Reading Instruction So it is important that you set your blade pitch correctly based on your RC helicopter manufacturer's recommendation, you RC Helicopter set-up and flying style. While some experienced RC Helicopter pilots can guess the pitch range without using a pitch gauge, it is very strongly recommended that you measure your pitch with a pitch gauge. Pitch readings below are used as example only to illustrate how to measure your heli pitch; it does not mean you have to set up your heli pitch range exactly like it is showed below. www.helitown.com /PitchGuage.html   (0 words)

Warp Drive Professional Protractor Mount the protractor at the tip of the blade with the protractor wheel towards the rear of the craft and the clamping bar towards the front of the craft. Hint: While rotating the blade with one hand close to the hub, gently rock the blade back and forth at the tip with the other hand. You will also want to pull out on the blades when setting the pitch to ensure that the blade collar is seated in the hub. www.warpdriveprops.com /protractor.html   (632 words)

Variable pitch boat prop - Patent 5527154 The center of pressure of each blade is offset downstream from the stub shaft axis, so that dynamic pressure on the blades tends to decrease blade pitch, while the rack and pinion tend to increase blade pitch. Prop "pitch", as used herein, means the helix angle of a chord of the prop, a chord being a line extending from the leading edge of the prop to the trailing edge. The forces tending to reduce blade angle are countered by the thrust on the blade, which tends to push the blades forward with respect to the hub, urging the pinions to roll "up" their racks, increasing the blade angle. www.freepatentsonline.com /5527154.html   (2429 words)

Dreissigacker Oars - Pitch Generally, the higher the rig, the less the pitch needed to feel comfortable and the lower the rig, the greater the pitch needed. Oar pitch should be measured separately by laying the oar face down with the blade on a level straight edge. Once the oar is in the proper position on the level straight edge, the pitch is measured with a level or pitch meter at the sleeve. www.concept2.com /us/products/oars/sweeps/pitch.asp   (608 words)

Variable pitch marine propeller system - Patent 4929201 A coupling are associated with the drive lugs of the bases and structured to hold the blades by the bases to align and simultaneously rotate the pitch of the blades in equal and opposite directions in response to movement of the coupling. A variable pitch marine propeller system according to claim 1, wherein the drive means comprise a hydraulically activated piston associated with the sliding block to move said sliding block forward or backward and alter the pitch of the blades. The operator may manually adjust the hydraulic line pressure to fix the pitch of the blades, or the hydraulic line pressure may be pre-set to adjust automatically in response to the propeller loads encountered at optimal engine performance. www.freepatentsonline.com /4929201.html   (4097 words)

ASK DJ Aerotech Question The angle between the local relative wind and the local blade pitch angle is the angle of attack of the blade at that location. The inboard portions of the blade have trouble making very much thrust efficiently, so on a well-designed prop the induced velocities on the inboard portions of the blade tend to be low, but the inflow velocities due to the plane's forward motion are still about the same as everywhere else on the blade. If the pitch angle is large, and the inflow velocity is small (such as during the beginning of the takeoff run), then the angle of attack is likely to be large. www.djaerotech.com /dj_askjd/dj_questions/blade_tipstall.html   (3445 words)

Saw Blade Terms If your table saw is not setup for the blade, if the blade gets a bit dull, the blade gullets do not clear the workpiece, or the blade has some pitch residue, the burnishing turns to burning. It is too soon to tell whether the blade will last longer between sharpenings than the Forrest, but I tend to believe it will because they tend to not collect as much pitch. This is important, because pitch leads to heat which is a prime cause of dulling blades. www.thewoodshop.20m.com /sawblades.htm   (1291 words)

Power Control of Wind Turbines The rotor blades thus have to be able to turn around their longitudinal axis (to pitch) as shown in the picture. The geometry of the rotor blade profile, however has been aerodynamically designed to ensure that the moment the wind speed becomes too high, it creates turbulence on the side of the rotor blade which is not facing the wind as shown in the picture on the previous page. As with pitch control it is largely an economic question whether it is worthwhile to pay for the added complexity of the machine, when the blade pitch mechanism is added. www.windpower.org /en/tour/wtrb/powerreg.htm   (912 words)

Stellafane ATM: Pour a Pitch Lap A pitch lap is used to polish and figure your mirror. The easiest way to remove pitch from its container is to shatter it into little bits with a hammer. An alternative to making facets with a razor blade is to "Micro-Facet" by pressing a plastic mesh bag, such as is used to for onions or potatoes, between the lap and mirror when hot or warn pressing. www.stellafane.com /atm/atm_grind/atm_pour_lap.htm   (1270 words)

Aeronautics - Aircraft Propulsion (PROPELLERS) The blade shank is thick for strength and fits into a hub which is attached to the crankshaft directly or indirectly. Blade pitch is loosely defined as the angle made by the chord of the blade and its plane of rotation, as shown in Figure 6-6. Feathering means to turn the blade approximately parallel with the line of flight, thus equalizing the pressure on the face and back of the blade and stopping the propeller. www.allstar.fiu.edu /aerojava/flight63.htm   (692 words)

0941 The blade grip is connected to a torque tube by a universal joint. When the blade flaps, it moves the torque-tube axially within the outer spline and this movement causes the torque-tube to rotate. This implies that positive delta3 causes an increase of the flap to decrease the pitch and negative delta3 causes an increase of the flap to increase the pitch. www.unicopter.com /0941.html   (0 words)

blade pitch (1 blade on the same plane as the 2nd blade) This is done at about 70 % throttle. Blade CX2 & Blade CP Future Phantom of the Opera. That incudes changing blade pitch from 0 to 100% throttle. www.rcuniverse.com /forum/fb.asp?m=5445761   (1085 words)

Ceiling fans - Casablanca fan motor model XLP2000   (Site not responding. Last check: ) The pitch (angle) of the fan blades has a big impact on the amount of air that a fan will move. However, fans that have a steeper blade pitch require more power to move the blades through the air. A slight difference in the pitch of the blades makes a huge difference in the amount of air you feel. www.hansenwholesale.com /casablanca/optpitch.html   (213 words)

Blade CP Repair - Maintenance Manual - Main Rotor - Setup and Adjustment I try to estimate the length of the tape needed and place it carefully on the light blade near the blade tip with the sticky side of the tape facing up. If you made any adjustments to the balance or are replacing blades, the track must be checked as outlined in the next section. Lengthen the Pitch Control Link (006, 007) of the low blade (the blade that made the lower mark on the paper). www.bladecprepair.com /man_mr_setup_and_adjustment   (1063 words)

Earthtoys - Emagazine Each of the autonomous pitch systems is equipped with an emergency power supply to immediately ensure the reliable functioning of the fast blade pitch system in the event of a total power failure. The pitch system is central to the turbine’s safety features, and is highly dependent on an effective energy storage system for both operation and emergency power. The nature of blade pitch control dictates that the motor be designed for maximum torque at very low rotational speeds, and that each blade be equipped with blade position sensors for control feedback. www.earthtoys.com /emagazine.php?issue_number=04.10.01&article=maxwell   (1151 words)

Blade-Pitch Control for Quieting Tilt-Rotor Aircraft NASA Tech Briefs - Find Articles This method is related to prior such noise-reduction methods, of a type denoted generally as higher-harmonic control (HHC), in which the blade pitch is made to oscillate at a harmonic of the frequency of rotation of the rotor. In general, the pitch angle of the rotor blades of a tilt-rotor aircraft is controlled by use of a swash plate connected to the rotor blades by pitch links. In the present method, one typically, chooses a control waveform that causes the blade pitch to oscillate sinusoidally at the N+l harmonic of the rotation frequency (where TV is the number of blades on each rotor). www.findarticles.com /p/articles/mi_qa3957/is_200403/ai_n9397965   (785 words)

Propellor Changes to a propeller's efficiency are produced by a number offactors, notably adjustments to the helix angle, the angle between the resultant relative velocity and the blade rotationdirection, and to blade pitch. However due to the shape of thepropeller only part of the blade can actually be operating at peak efficiency, the outer part of the blade produces the mostthrust and so the blade is positioned at a pitch that gives optimum angle to that portion. Since a large portion of the blade istherefore at an inefficient angle the inboard ends of the blade are subsumed into a streamlined spinner to reduce the resistancetorque that would otherwise be created. www.altvetmed.com /face/44001-propellor.html   (377 words)

Lamps Plus | Design Trends   (Site not responding. Last check: ) If the fan has a small motor and high blade pitch, the force of pulling the blades through the air will not only slow down the motor but eventually that motor will overheat from working too hard. Ceiling fan blades should be made of multiple layers of pressurized hardwood to eliminate warping. Some less expensive blades are made of particle board, which looks great in the beginning but will bend and warp with time. www.lampsplus.com /htmls/fantips/fantips3.asp   (179 words)

Propeller Blade Area & Pitch, Tuning Propellers by WILDCAT In order to achieve maximum performance it is necessary to balance the blade area with the effective pitch of the propellers. Blade area on a propeller produces the thrust that gets the boat moving and keeps it going once underway. Blade area is directly related to diameter and number of blades and is often referred to as D.A.R. As diameter increases so does blade area. www.wildcatprops.com /articles-blade-pitch.asp   (0 words)

Individual blade pitch control   (Site not responding. Last check: ) This project aims to improve the understanding of the measurements required to perform effective individual blade pitch control, with the goal of enabling mitigation of structural vibrations during conditions of non-uniform inflow. We have used distance-based control theoretic concepts to quantify the importance of modelling errors on the predictions made using simplified models of the aeroelastic turbine dynamics. A range of sensors is considered, from measurements in the tower and nacelle, to drivetrain measurements, measurements on the hub and blade roots, and aerodynamic measurements at outboard blade positions. www.forskningscenter.dk /vea-ves/projects/signalsforpitchcontrol   (312 words)

Blade CP Repair - Maintenance Manual - Bell Hiller Upgrade If you have a pitch gauge I recommend you take a neutral reading prior to the upgrade and then adjust the Pitch Control Links (006/007) to return to neutral after the upgrade. Using two 1.5mm hex wrenches remove one of the Blade Grip retaining screws (013) and then remove both Blade Grips, Spindle (016), O-rings (038) and Washers (015, 039 and 040). When you are sure that the Grips are installed correctly tighten the Blade Grip retaining screws (013) using two 1.5mm hex wrenches. www.bladecprepair.com /man_bh_upgrade.html   (465 words)

CarterCopter - How the CC controls its Rotor Disk Tilting a 2-bladed rotor disk is usually achieved by applying a 'cyclic-pitch' change to the rotor blades which then with the aid of the see-saw hinge (and obeying the laws of aero-dynamics *or* gyroscopic precession), fly to a new plane-of-rotation where the lift between the blades balances out again thus effectively 'tilting' the rotor disk. Tilting the swash-plate applies 'direct' cyclic pitch change to the rotor blades which fly to a new plane-of-rotation which in turn means a tilt in the rotor disk. If a pitch change control rod is connected to the blade-pitch-arm directly in line with the teeter hinge then the blade pitch remains the same when flapping. www.internetage.com /cartercopters/writeups6.htm   (2029 words)

Hovercraft,Air Cushion Vehicle,Air Boat Propellers,Fans,Parts,Supplies, components and advice. AMCA style A duct or 14,100 cfm @ 30 degrees blade pitch requiring 16.8 hp; or 15,500 cfm @ 32.5 degrees blade pitch requiring 20 hp; or 17,100 cfm @ 35 degrees blade pitch requiring 23 hp; or 18,200 cfm @ 37.5 degrees blade pitch requiring 25.5 hp. Fixed blade pitch available (degrees): 25, 30, 35, 40 and 45. 32" Hovercraft Thrust Fan (type 4) with 9 blades-- fiberglass-reinforced polyamide blades are resistant to water and UV rays. www.hoverhawk.com   (0 words)

Blade Pitch The blade pitch adjustment is a working tool that supports the cutting action of the blade and is hydraulically controlled by a lever in the operator's cab. For normal grading operations, the upright position on the blade is used. When selecting the correct blade pitch, you have to think about the type of operation, type of material, depth of cut, and speed of operation. www.tpub.com /eqopbas/109.htm   (395 words)

Tail Pitch A common confusion about the tail pitch is that the blades should be straight when the stick is in the center. In the case of the Raptor and all other helicopters with a clockwise rotating main blade, the body would be forced in an anti-clockwise direction (nose moves to the left). With the rudder stick on the radio centered and the trim centered there should be 4.5mm between the pitch slider and the tail rotor casing with the collective stick centered up/down and left/right. www.raptortechnique.com /tailpitch.htm   (863 words)

Sport Aviator The Blade is a delight to fly indoors, but the typical living room isn’t the practical place because of its size. The switch on the transmitter changes the collective pitch control so that zero blade pitch is at the center of the stick travel. In a hover the sweet spot to hold the Blade at one height was between one of the notches on the throttle. www.masportaviator.com /ah.asp?CatlID=15&ID=127   (2355 words)

Removing Blade Pitch - Canadian Woodworking Forum If the blade is really bad then it needs to soak for a while. I soak the blade in warm water and baking soda and then scrub it with an old toothbrush. Eh Dan its been my experience to keep cleaner around but I do find that with the meriad of different blades that using the right blade for the job nearly eliminates the need for cleaning. www.canadianwoodworking.com /forum/showthread.php?t=842&goto=nextoldest   (162 words)

Try your search on: Qwika (all wikis)

About us   |   Why use us?   |   Reviews   |   Press   |   Contact us   Copyright © 2005-2007 www.factbites.com Usage implies agreement with terms.