
	Where results make sense

Topic: Molten wax

	Wax play - Wikipedia, the free encyclopedia
		Wax play is a form of sensual play involving warm or hot wax usually dripped from candles or ladled onto a person's naked skin.
		Wax play may be combined with other BDSM or sexual activity.
		Wax may be difficult to remove, particularly from areas with hair.
	en.wikipedia.org /wiki/Wax_play (536 words)

	Casting - Wikipedia, the free encyclopedia
		Once the plaster and latex mould is finished, molten wax is poured into it and swished around until an even coating, usually about ¼ inches thick, covers the entire inner surface of the mould.
		Each hollow wax copy is then "chased": a heated metal tool is used to rub out all the marks which show the "parting line" or "flashing" where the pieces of the mould came together.
		Molten metal is poured into an open-ended, water-cooled copper mould, which allows a 'skin' of solid metal to form over the still-liquid centre.
	en.wikipedia.org /wiki/Lost_wax (4344 words)

	Frontier Wax - Glossary
		The cloud point is the temperature where liquid molten wax is beginning to change structurally and visibly from liquid to solid.
		Fully refined paraffin is a wax that has been separated from crude oil, as a semi-refined wax, and fully refined, through several more stages, at a refiner, to remove essentially all of the unwanted contaminants from the paraffin wax.
		Semi-refined paraffin is a wax that has been separated from crude oil, as a slack wax, and refined, through one further stage, at a refinery, to remove almost all of the unwanted contaminants from the paraffin wax.
	www.frontierwax.com /glossary.html (1042 words)

	Original sculptures and recreated in bronze using the lost wax method (Site not responding. Last check: 2007-10-29)
		The molds are then used to form wax figures; molten wax is poured into the rubber mold, producing a perfect copy of the original sculpture.
		The wax casting is removed from the mold, and a trained artisan hand- finishes the wax pattern to original perfection.
		Wax rods (gates) are attached to the wax pattern to allow the even flow of molten metal and to alleviate the trapping of air and gas.
	harlanbronze.com /Pages/foundry.html (368 words)

	The Bronze Casting Process
		To make a wax cast, molten wax is painted into the rubber mould, taking care not to trap any air pockets in the surface and is gradually built up to an even thickness.
		After trimming any excess from the edges, the sections of the mould are assembled and through an aperture made for the purpose, cooling molten wax is poured in and then out of the mould.
		The wax needs to be encased in a mould able to withstand the high temperature required to melt out the wax from inside.
	www.laurencebroderick.co.uk /casting_2.html (447 words)

	Glossary
		The wax is solidifying as it touches the mold and as the wax rises, so do the marks.
		A container candle is a candle made by pouring the molten wax into a container such as a glass jar, glass candle holder, aluminum travel tin, or any other vessel.
		The wax used in pillars generally has a higher melting point so that (when using the correct size wick) the outer part of the candle remains solid and the pool of molten wax spreads to about within a 1/4" of the edge of the candle.
	www.canwax.com /page/page/504506.htm (980 words)

	Sinopia.com \| Encaustic Hot Wax Painting
		Pigment is added to molten bees wax and (often) resin, which is applied to a surface.
		As in the Wax Paste, the beeswax is heated in a double boiler waterbath and combined with 3 parts of the Turpentine.
		Wax paste is extremely flammable and difficult to extinguish once lit.
	www.sinopia.com /encaustic.html (479 words)

	Tina Allen: THE LOST WAX PROCESS (Site not responding. Last check: 2007-10-29)
		Molten wax is then poured into the rubber mold, producing a faithful casting of the original.
		Wax rods called gates are applied to the wax casting to allow the wax to be removed and funnels called sprues are attached to receive the molten bronze.
		The wax casting is coated with several layers of a liquid refractory ceramic, creating a stable mold which is allowed to cure for several days.
	www.tinaallen.com /lostwax.php (277 words)

	Value-added products from beekeeping. Chapter 4.
		Wax is used to cap the ripened honey and when mixed with some propolis, also protects the brood from infections and desiccation.
		Wax from other honeybee species (ghedda wax) is very similar, but has characteristics sufficiently different for it not to be used by the cosmetic industry.
		Waxing of the threads on pipes was reported to prevent joints from corroding or locking and simultaneously made them waterproof (Brown, 1981).
	www.fao.org /docrep/w0076e/w0076e12.htm (6782 words)

	Method of making lipstick samplers - Patent 6015513
		The distribution of wax occurs as a consequence of centrifugal force on the droplet 30 as the spindle is turnably driven.
		The spinning also causes a rapid cooling of the coating 28 of the wax material, all to the end that a relatively uniform and smooth finish is imparted to the outer surface of the coating 28 on the tip portion 26.
		However, depending on the viscosity and other characteristics of the wax material being applied, it may be desirable under some circumstances, to commence turning of the spindle 14 while the plastic form 16 is still immersed, either partially or wholly, such variations being considered to fall within the scope of the invention.
	www.freepatentsonline.com /6015513.html (3266 words)

	Method of making chewing gum with wax-coated delayed release ingredients - Patent 4885175
		Because the wax is added in a molten state, it is important for the wax in the first coat to have a melting point higher than the wax in the second coat.
		The amount of molten wax needed to produce a mix of this consistency will vary depending on the specific wax chosen and the specific ingredient to be coated.
		Preferably, the amount of molten wax is between about 10 and about 50 weight percent of the damp mix, more preferably between about 15 and about 45 weight percent, and most preferably between about 25 and about 40 weight percent.
	www.freepatentsonline.com /4885175.html (6975 words)

	The Four Winds Collection - The Lost Wax Bronze Process
		The wax casting is removed from the mold, and a trained artisan hand-finishes the wax pattern to original perfection.
		Wax rods, called gates, are attached to the wax pattern to allow the even flow of molten metal and to alleviate the trapping of air and gas.
		The patina is sealed under a wax coating and becomes a permanent part of the sculpture.
	www.classicbronze.com /process.html (499 words)

	Lost Wax Casting Process
		This wax model is an exact duplicate of the original casting.
		STEP 3 Chasing the Wax: The wax is pulled from the mold and hand chased (re-detailed) by a skilled artisan.
		The shell bakes and the wax is melted (lost) from the shell.
	store.worldbronzes.com /lowaxprin.html (434 words)

	Elegance In Bronze - Lost Wax Casting Process
		Molten wax is poured into the mold to form layers of wax.
		The wax is pulled from the mold and hand chased (re-detailed) by a skilled artisan.
		Wax rods (gates) and pouring cup are attached to the wax casting in just the right positions.
	www.bronzeart.com /lostwax.html (379 words)

	Wax Magick
		The shape formed by the molten wax are very easy to read so may be worth the expense.
		If you try wax divination several times with only dots coming up each time, you're either asking the wrong questions or, if you haven't asked one, you shouldn't be seeking a glimpse into the future at this time -- at least not through wax and water.
		When the wax is melted, remove the can of double-boiler carefully from the pot with holders and take it to the vessel of water.
	users.bigpond.net.au /raidne/waxmagick.htm (1248 words)

	WHAT DOES LOST WAX CASTING MEAN
		The wax is "burned out" in a kiln at 1250° F (orange hot), so that it goes up in smoke and leaves its impression in the ceramic.
		When the metal is thoroughly molten, the centrifuge is spun (in this case) to force the metal into the mold so that it will assume the same shape that the wax formerly had.
		Molten wax is forced into the rubber mold, hardening into a "positive" copy of the original metal.
	www.castofcharacters.com /lostwax.htm (520 words)

	Decorative candle and method of manufacturing the same - Patent 6214295
		The wax is allowed to cool such that it solidifies and is then removable from the mold thereby forming the candle.
		At this point, while the wax 26 is molten, the desired fragrance and/or pigment may be mixed with the wax 26.
		The melting point of the wax 26 is lower than the melting point of the gelatinous components 34 such that the components 34 do not melt when placed within molten portion 36.
	www.freepatentsonline.com /6214295.html (2974 words)

	making wax candles
		The methods most commonly used for making beeswax candles are to pour molten wax into molds, to dip wicking into the melted wax or to roll a sheet of beeswax foundation around a wick.
		Once the wax has melted, pour the molten wax through a filter and set it to cool.
		Wax that is first melted or even cleaned, can be poured into milk cartons for storage.
	gears.tucson.ars.ag.gov /beeclass/wax/candles.html (1754 words)

	Lost Wax Casting : anvilfire iForge Demo
		The process of cire’ perdue or "lost wax" casting derives its name from the fact that the model is created from wax that is cast into plaster and then burned out of the plaster leaving a cavity that exactly matches the model.
		It is sealed to the base plate with a little molten wax to keep it in place when the investment is poured in.
		The finished flask needs to have all the wax and wax residues burned out completely, or they will vaporize when the molten metal hits them, causing all kinds of problems and risks to your personal safety.
	www.anvilfire.com /iForge/tutor/vi_copper_c1/index.htm (3426 words)

	Researcher models ocean floor's tectonic evolution (Site not responding. Last check: 2007-10-29)
		Instead he is watching a model of tectonic evolution in a tub of molten wax.
		The solid wax layer represents the Earth's cold and hard lithosphere, and the molten wax below, the Earth's plastic upper mantle.
		Each chunk of wax grows with constant velocity in the direction of the rift, slowing down the rotation rate and resulting in a spiral shape.
	www.news.cornell.edu /Chronicle/99/4.1.99/APS_ocean.html (363 words)

	EDSE 452/453 Inquiry Demonstration
		Since it is the wax that allows a candle to burn, a flame held within the smoke trail lights these particles, causing the flame to “travel” to the wick.
		Light the candle and allow it to burn so the wax begins to melt and the flame is a good size.
		The molten wax is absorbed by the wick and the wax vapors are burned around the wick, allowing the candle to continue to burn.
	www.quasar.ualberta.ca /edse456/apt/inquiry/magicandle.htm (373 words)

	Bees Wax Candles (Site not responding. Last check: 2007-10-29)
		If the opposite process (solidification of the wax occurs at a lower temperature, a larger amount of liquid will accumulate in the depression surrounding the wick, and the molten wax with overflow the walls of the depression (that is "drip").
		Sometimes candles are layered with a lower melting wax as the core and a higher melting wax as the outer layer.
		Female worker bees secrete wax from four pairs of special glands, called wax glands on the underside of their abdomens.
	www.newton.dep.anl.gov /askasci/gen01/gen01694.htm (298 words)

	Dictionary of Candle Terms
		A candle flame must have a pool of fuel (molten wax) to draw from, so if you burn a votive on a flat holder or a plate, the burning time will be shorter because the candle will loose it's shape and basically become a puddle, drowning out the wick.
		For wax it is the temperature that wax would have to reach before it combusts and catches fire.
		Petrolatum is the wax byproduct of the heaviest lube oil, bright stock.
	www.candlecauldron.com /dictionary.html (1125 words)

	Equiva Services - MSDS
		Eye Irritation: Molten wax fumes may be slightly irritating to eyes.
		Molten wax will cause burns on contact with eyes.
		If wax is molten, store at a temperature not more than 10 deg.
	www.equivashellmsds.com /getsinglemsds.asp?ID=196565 (1941 words)

	Lost Wax Investment Casting Process
		From the designer's blueprint or CAD data, a wax injection die is made to receive molten wax injected under pressure.
		For prototypes, plastic patterns, SLA's, or machined waxes are fabricated; eliminating mold construction time and cost.
		The wax or prototype patterns are mounted to a wax tree with suitable gates and runners.
	www.protocastjlc.com /lost_wax_process.htm (142 words)

	Usenet Replayer message view <3ade43d1.12225570@news.videotron.ca>
		Ideal wax temperature for dipping is between 150F and 155F.
		the molten wax, and will release the candle when it has cooled.
		C) Pour wax on a cookie sheet to a depth of 5 mm and allow to harden.
	www.usenet-replayer.com /faq/bit.listserv.candle-l.html (1884 words)

	Modeling Ocean Floor Spreading In Tub Of Wax
		His experimental apparatus, 3 feet long, 1 foot wide and 4 inches deep, is filled with molten wax.
		The solid layer of wax is divided, and the two halves are pulled apart with constant velocity.
		They are tiny chunks of solid wax that appear at the rift and begin rolling up, something like a rolling snowball gathering snow.
	www.eurekalert.org /pub_releases/1999-03/CUNS-MOFS-240399.php (606 words)

	History of Encaustic Wax Painting and Art
		This is a process of applying molten wax colours to a surface for the creation of images, decoration and so forth.
		The wax colours appear to have been applied with some swiftness which would certainly make sense if the wax was molten and liable to cool on the brush if not handled with some speed.
		Anyway, once molten the pigments might have been blended into a volume of wax and applied to the wood surface by brush.
	www.encaustic.com /features/history/history.html (751 words)

	Arts Encaustic ~ Home of Creative Waxart
		The reason that wax is such a wonderful medium for this activity is that you can always change things that you do not like.
		The waxes can be reworked or removed, added to or abraded.
		To work with wax in any manner is to encounter a completely new world.
	www.encaustic.com (158 words)

	Wax, Molten (Site not responding. Last check: 2007-10-29)
		This molten gravity filling machine is filling shoe polish into metal tins.
		We make machines that feed containers, pre heat containers, fill them with wax, cool them, top off candles with a second fill, and label them all in one process.
		The NPS molten filling systems will fill and handle votives to large pillar candles using the same equipment.
	www.neumannpackaging.com /wax,_molten.htm (136 words)

Try your search on: Qwika (all wikis)