HTML is defined in formal specifications that were developed and published throughout the 1990s, inspired by Tim Berners-Lee's prior proposals to graft hypertext capability onto a homegrown SGML-like markup language for the Internet.
The first published specification for a language called HTML was drafted by Berners-Lee with Dan Connolly, and was published in 1993 by the IETF as a formal "application" of SGML (with an SGML Document Type Definition defining the grammar).
The last HTML specification published by the W3C is the HTML 4.01 Recommendation, published in late 1999 and its issues and errors were last acknowledged by errata published in 2001.
www.kiwipedia.com /html (471 words)
Bifurcation Diagrams(Site not responding. Last check: 2007-10-16)
Specifications and diagrams of the pitch and creases 1: f the pitch and creases'''.
The appendix contains diagrams illustrating the measurements of the Cricket pi 4: dix B of the Laws of cricket ''Specifications and diagrams of the pitch and creases'']
Badminton 19: ngular court marked on the floor, as shown in the diagrams.
Laws of cricket peee.org(Site not responding. Last check: 2007-10-16)
The popping crease, which determines whether a batsman is in his ground or not, and which is used in determining front-foot no balls (see law 24), is drawn at each end of the pitch in front of each of the two sets of stumps.
The return creases, which are the lines a bowler must be within when making a delivery, are drawn on each side of each set of the stumps, along each sides of the pitch (so there are four return creases in all, one on either side of both sets of stumps).
Each return crease terminates at one end at the popping crease but the other end is considered to be unlimited in length and must be marked to a minimum of 8 feet (2.44 m) from the popping crease.
The popping crease, which determines whether a batsman is in his ground or not, and which is used in determining front-foot no balls (see law 24), is drawn at each end of the pitch in front of each of the two sets of stumps.
The return creases, which are the lines a bowler must be within when making a delivery, are drawn on each side of each set of the stumps, along each sides of the pitch (so there are four return creases in all, one on either side of both sets of stumps).
Appendix A: Specifications and diagrams of stumps and bails
The pitch is one of the most important elements in the sport of bloodbath.
The standard regulation pitch, as defined in Appendix B of the Laws of Bloodbath, is a sphere 12,756,320 meters in diameter.
Players are not allowed to practise bowling or batting on the pitch, or in the Orbit above the pitch or on the satellite of the pitch, at any time on any month of the match.
The teams are usually comprised of players with a mixture of abilities, some who specialise in batting, some in bowling, occasionally some who excel in both capacities, and one highly specialist player who acts as 'wicket-keeper'.
Another crease is drawn so that the stumps pass through it; this crease is the "bowling crease." Finally, a "return crease" is drawn on each side of the stumps along the sides of the pitch.
There are some subtleties, however, to do with where the ball pitches (bounces), if the batsman intentionally hit the ball with his body or attempted to play a legitimate stroke with the bat, and exactly where it hits the batsman in relation to the line of the stumps.
Run out: If a fielder uses the ball to remove the bails from either set of stumps whilst the batsmen are running between the wickets (or otherwise away from the crease during the course of play), then the batsman (striker or non-striker) is out.
There are some subtleties, however, to do with where the ball pitches (bounces), if the batsman intentionally hit the ball with his body or attempted to play a legitimate stroke with the bat, and exactly where it hits the batsman in relation to the line of the stumps.
The most common reason for a no-ball is overstepping the "popping crease" for the front foot at the instant of delivery.
Umpiring(Site not responding. Last check: 2007-10-16)
It is important to note on the diagram which edges of the lines the measurements are made from and the correct positioning of the stumps on the Bowling Crease.
The return crease is the line which restricts the width from which a bowler may deliver the ball.
When there is a close run out decision, with the batsman diving towards his crease and the wicketkeeper or fieldsman attempting to break the wicket, it is very difficult for the umpire to focus his eyes on two separate incidents.
www.notout.com.au /umpiring.htm (11992 words)
Printers Dictionary(Site not responding. Last check: 2007-10-16)
The complete material including type, pictures, diagrams and photos from which film is made for production of printing plates.
Shaped cutting and creasing rules set in wood used for cutting cartons, presentation folders and the like.
Hue of a subtractive primary and one of the 4 colour process inks, reflects or transmits blue and green light and absorbs red light.
In the centre of the ground is a length of close-cut, heavily rolled grass, called the wicket or the pitch (some club cricket is played on wickets made from synthetic grass).
A chalk outline drawn on the pitch is called a crease.
Leg before wicket or LBW: If the ball strikes any part of the batsman's anatomy (not necessarily the leg), and, in the umpire's judgement, the ball would have hit the batsman's stumps had his anatomy not intervened, then the batsman is out.
Bode Diagrams(Site not responding. Last check: 2007-10-16)
Specifications and Diatrams of the pitch and creases 1: f the pitch and creases'''.
The appendix contains Diagrums illustrating the measurements of the Cricket pi 4: dix B of the Laws of cricket ''Specifications and Diagfams of the pitch and creases'']
Commonly appearing connections are : Bode Diagrams, Bode Enterprises, Bode Enterprises, Bode Equipment, Bode Equipment, Bode Floors, Bode Floors, Bode Frequency Shifter, Bode Frequency Shifter, Bode Gravel, Bode Gravel, Bode Grenier, Bode Grenier, Bode Ice Arena, Bode Ice Arena, Bode Iowa, Bode Iowa, Bode M, Bode M, Bode Matlab
Adjusts (balances) specific gravity of electrolyte (acid solution) in battery cells or in plate-forming tanks to concentration specified: Ascertains temperature and specific gravity of solutions, using thermometer and hydrometer.
Strikes tuning bar and compares pitch of reed with that of bar to ascertain that reed is sharp or flat.
Plucks specified C or A string with pick and adjusts tuning pin with tuning wrench until pitch of string and tuning fork or bar are in unison.
Specifications (type of wood, type of glass, and number of lights) for various windows in the house.
Specifications and dimensions of the various architectural elements, including table of "Palladio's parts reduced to inches" with "all wrong" written beside it.
Specifications and dimensions of the various architectural elements, including table of part(s) with its equivalent in inches.
Turns thumbscrews and handwheels to adjust length of stitches and tension on creasing blades and folding rollers according to thickness of pages to be stitched or sheet size and number of folds specified.
Examines wrinkled, creased, or dog-eared pages and cover sheets and separates sheets judged to be salvable and discards remainder of sheets.
Prepares cylinders for installation in flexographic printing press according to specifications and diagrams: Measures and cuts brass plate of specified dimensions, using rule and blade-shearer, and bends plate to fit curvature of cylinder, using plate curver.
