
	Where results make sense

Topic: Wire drawing

	Wire - Wikipedia, the free encyclopedia
		Wire is usually drawn of cylindrical form; but it may be made of any desired section by varying the outline of the holes in the draw-plate through which it is passed in the process of manufacture.
		Wire has to be pointed or made smaller in diameter at the end before it can be passed through the die; the pointing is done by hammering, filing, rolling or swaging in dies, which effect a reduction in diameter.
		Wires and cables for electrical purposes are covered with various insulating materials, such as cotton, rubber, or plastic, wrapped in concentric fashion and further protected with, substances such as paraffin, some kind of preservative compound, bitumen or lead sheathing or steel taping.
	en.wikipedia.org /wiki/Wire (2069 words)

	Making Wire
		Drawing is performed on the draw bench, which comprises the draw plate and a power reel for pulling the wire through.
		In wet drawing, the wire is given a lees coating by passing it through lees liquor composed of water and some kind of flour, sometimes fermented and sometimes mixed with milk of lime.
		In galvanizing, the wire is passed (a) through a lead bath to anneal it; (b) through a weak pickling solution to remove the scale formed; (c) through a rinsing bath; and (d) through the molten spelter contained in the galvanizing pan.
	www.sizes.com /library/making_wire.htm (977 words)

	[Ganoksin] Jewelry Making - Wire Drawing Hints
		The trick to drawing wire by hand is to grasp the tapered end that sticks out the front of the drawplate with the pliers in such a way that there are some 5 mm of play; of movement back and forth to the drawplate.
		For example a square or round wire is flattened, folded over, soldered to close the 'loop' and drawn through a square hole in the drawplate to produce two triangular wires.
		A draw bench is extremely useful and one may be constructed from wood and canvas or with a boat winch and board.
	www.ganoksin.com /borisat/nenam/wdraw.htm (936 words)

	Production of cold-drawn, round wireD3;15= (No Responses);13= (1 Response);14= (% Responses) (Site not responding. Last check: 2007-11-04)
		Drawing takes place in drawing machines, in which the motor power is transmitted from the block motor(s) to the wire via the block(s).
		The drawing dies and the blocks for dry drawing are therefore cooled with water to reduce the temperature.
		Wire to be further drawn is prepared with a lubricant carrier, mainly depending on type of drawing method.
	www.sandvik.com /sandvik/0140/SM/se01240.nsf/f9aff13490287b65ea2564f50042c670/0729fae1c94c32dc4125680a006b9244!OpenDocument (4191 words)

	Fine Wire Drawing Machines - Jaikvin Enterprises, India
		This pointed wire is inserted through the die of the first Wire Drawing Machine and fastened to a locking device on the drum.
		The starting end of the drawn wire is released from the lock of the first drum, is passed through the overhead loop and pulley provided, is brought down and is inserted through the die of the second drum and drawn through this die for further reduction.
		Thus, the wire is drawn through all the wire drawing drums of the set in a continuous manner to get the required finished diameter of the wire.
	www.jaikvin.com /WireFine.html (557 words)

	wire drawing -- Britannica Concise Encyclopedia Online Article
		Fine wire is made by a multiple-block machine, because the reduction cannot be performed in a single draft.
		The cold drawing of wire is an important and special sector of steelmaking.
		Their sound is produced when a slender length of material—usually wire, plastic, silk, or animal gut—is made to vibrate by being stroked with a bow, plucked with a finger or plectrum (pick), or struck with a harder object.
	www.britannica.com /ebc/article?tocId=9382832 (860 words)

	Wire Drawing
		The art or process of wire drawing like the name implies is to draw a wire of a bigger diameter through a hole with smaller diameter hereby reducing the diameter through plastic deformation while the volume remains the same.
		The wire ends are secured by two clamps one end to each clamp and the wire ends are then moved together at the same time as electricity is passed between the two clamps through the wire.
		The drawing blocks are made of forged C 50 carbon steel, induction tempered at medium frequency, to obtain a surface hardness of approximately 60 HRC.
	www.wireworld.com /seminar/wiredrawing (2667 words)

	The 2006-2011 World Outlook for Steel Wire Drawing
		It is for this definition of steel wire drawing that the aggregate latent demand estimates are derived.
		Wire, iron or steel (e.g., armored, bare, insulated), made in wire drawing plants.
		Based on the aggregate view of steel wire drawing as defined above, data were then collected for as many similar countries as possible for that same definition, at the same level of the value chain.
	www.marketresearch.com /redirect.asp?productid=1112729&progid=3603 (3181 words)

	Mechanical equipment: Wire drawing
		It allows to draw wires from 15 mm down to 0.5 mm in successive passes.
		The drawing dies are made of tungsten-carbide (with cobalt-binder).
		Before each pass the wire is pointed with a swaging machine; it is then inserted through the conical die and clamped to the drawhead.
	www.mtm.kuleuven.ac.be /Research/Equipment/Mechanical/WireDrawing.html (85 words)

	Wire Mesh\|welded wire mesh\|stainless steel wire mesh\|Wire Cloth\|galvanized wire\|wire mesh fencing\|Pvc wire mesh wire ... (Site not responding. Last check: 2007-11-04)
		Wire Meshwelded wire meshstainless steel wire meshWire Clothgalvanized wirewire mesh fencingPvc wire mesh wire netting,barbed wire,wire netting,razor wire,barbed tape wire,barbed wire fences,galvanized wireGalvanized Wirewire clothwelded mesh,wire cloth,welded wire mesh, stainless steel wire mesh, coated wire mesh, wire mesh fencing, woven wire mesh, galvanized wire mesh, wire mesh factory, metal wire mesh, wire mesh screens
		Anping Mingzuan Wire Mesh Factory is a manufacturer of woven wire mesh (stainless steel woven wire mesh, brass woven wire mesh, mild steel woven wire mesh, wire woven conveyor belt), welded wire mesh (PVC coated welded wire mesh, galvanized welded wire mesh...
		Buffalo, NY specializes in wire drawing, galvanizing and wire mesh weaving, mainly galvanized iron wire, welded iron wire mesh, galvanized square wire mesh, other iron woven wire mesh, stainless steel wire, stainless steel wire mesh, crimped wire mesh, for more: http://www.wiremesh-wanda.com.
	mesh.freewebpage.org (2373 words)

	Sherburne Metals- Wire Drawing
		Wire drawing and insulated wire and cable production have always been strong and continually growing application areas for Sherburne rod and wire products.
		As a result, Sherburne copper is now used in insulated wire and cable products ranging from power cable to control wire and high-speed telecommunications products.
		Our copper is also used as magnet wire in motors and generators...
	www.sherburnemetals.com /applications/html/wiredrawing.html (220 words)

	Wire Drawing (Site not responding. Last check: 2007-11-04)
		Wire drawing is a metal-reducing process in which a wire rod is pulled or drawn through a single die or a series of continuous dies, thereby reducing its diameter.
		Because the volume of the wire remains the same, the length of the wire changes according to its new diameter.
		Increases the length of the wire as its diameter decreases
	class.et.byu.edu /mfg130/processes/descriptions/deformation/wiredrawing.htm (124 words)

	2002 NAICS Definitions: 331222 Steel Wire Drawing
		This U.S. industry comprises establishments primarily engaged in drawing wire from purchased steel.
		Drawing iron or steel wire from purchased iron or steel
		Drawing iron or steel wire from purchased iron or steel and fabricating wire prod
	www.census.gov /epcd/naics02/def/ND331222.HTM (303 words)

	Wire Mesh\|Wire Cloth\|stainless steel wire mesh \|stainless steel wire cloth\|expanded metal mesh\|expanded metal ...
		Wire MeshWire Clothstainless steel wire mesh stainless steel wire clothexpanded metal meshexpanded metal clothbrass woven wire mesh
		Unlike most companies doing only wire mesh weaving or wire drawing, Wanda emphasizes both wire drawing and wire mesh weaving, and has earned very good reputation among customers in both lines.
		Wanda has now 26 sets of stainless steel wire drawing machines and 15 sets of iron wire drawing machines, 6 wire galvanizing production lines and 40 sets of wire mesh weaving and welding machines.
	www.wiremesh-wanda.com (335 words)

	Department of Energy Information Bridge - full-text scientific and technical reports (gray literature) (Site not responding. Last check: 2007-11-04)
		One set of hardware provided rigid alignment of the wires to their wire drawing die axes within 0.35 degrees using ''hydrostatic pressure stiffening'' to enable the precision guidance strategy to be implemented for these highly flexible small diameter wires.
		Research findings and results: In Phase 1, a breakthrough in wire drawing technology for A-15 superconductor composites was achieved by dramatically limiting or eliminating breakage in four different A-15 composite precursor wire designs during the drawing of these very desirable composites that previously could not be drawn to near final size.
		A portable Advanced Wire Drawing Station will be developed and constructed in the final stage of the proposed Phase 2 program and it will be used in an outside manufacturing facility for superconductor composite wire drawing field trials.
	www.osti.gov /bridge/product.biblio.jsp?osti_id=810974 (602 words)

	What is wire drawing? (Site not responding. Last check: 2007-11-04)
		Wire drawing is an operation to produce wire of various sizes within certain specific tolerances.
		The process involves reducing the diameter of rods or wires by passing them through a series of wire drawing dies with each successive die having smaller bore diameter than the one preceding it.
		The final wire size is reached as the wire passes through the last die in the series.
	www.e6.com /e6/page.jsp?pageid=600406065 (126 words)

	wirenet.org Forums - wire drawing problems
		First I am assuming you are talking about copper wire and that you are using a water based lubricant.
		- That the drawing dies fit properly in their die holders and that the holders are firmly attached to the drawing machine.
		(5) Make sure the drawing dies fit properly in their die holders, that the holders are firmly attached to the drawing machine and that the wire is properly guided to each die.
	www.wirenet.org /forum/printthread.cfm?Forum=12&Topic=82 (1286 words)

	Wire Drawing Machine Operator: A description for the wire drawing machine operator job
		Wire Drawing Machine Operator - Operates wire drawing machine to shape or emboss wire used in dental work and costume jewelry: Reviews work orders and selects shaping, reducing, or embossing roller dies according to specifications.
		Positions roller die in machine that shapes, reduces, or embosses wire, for example gold, silver, or copper, to form dental or jewelry wire.
		May also measure physical properties of wire, for example tensile strength and bend set, and calculate elongation data, using test instruments and calculator.
	www.job-descriptions.org /wire-drawing-machine-operator.html (222 words)

	Wire drawing, wires, press tools, plastic mold tools, cutter, dies, twisting dies (Site not responding. Last check: 2007-11-04)
		Manufacture, Wholesale and Retail of Diamond and Carbide Draw Dies used to size and draw wire, including dies, transfer fingers, wire sizing rings and diamond powder used to fine size wire.
		Manufacturers of tungsten carbide wire drawing dies and associated products including rolls spinner, shaving, shaped dies, press tools, plastic mold tools, cutter, dies, twisting dies, drive rolls, chain dies, clutch dies, etc.
		Wire drawing, cable machine, stranding, bow twister, Ajmer, India, Rajsthan.
	www.bizahead.com /directory/industrial/machinery_tools/wire/index.shtml (258 words)

	Wire World
		ATOFINA Chemicals, Inc. is a supplier of specialty lubricants to the wire drawing industry that reduce costs, yet improve the worker environment such as the recently introduced family of pelletized wire drawing lubricants that are virtually dust free and safer for the environment.
		Buttwelders for ferrous and non-ferrous wire and Welders for stranded conductors
		Wire Lab also makes two models of Lubricant Applicators designed to snap on the rod or wire in the lubricant section of the die box.
	www.wireworld.com /prog/newlistings.html (12865 words)

	2002 NAICS Definitions: 331422 Copper Wire (except Mechanical) Drawing
		This U.S. industry comprises establishments primarily engaged in drawing or drawing and insulating communication and energy wire and cable from purchased copper or in integrated secondary smelting and wire drawing plants.
		Manufacturing copper mechanical wire from purchased copper or by recovering copper from scrap and drawing or extruding--are classified in U.S. Industry 331421, Copper Rolling, Drawing, and Extruding;
		Wire cloth, copper, made in integrated secondary smelting and wire drawing plants
	www.census.gov /epcd/naics02/def/ND331422.HTM (384 words)

	Welcome to the Wire Die Inc. Web Site (Site not responding. Last check: 2007-11-04)
		Wire Die, Inc., a wholly owned subsidiary of ACS Industries, Inc. was created from over sixty years of wire drawing experience.
		By making our own dies, we can control the the quality and size of the diamonds as well as the way in which the diamonds are mounted.
		As a result, Wire Die, Inc. has developed dies that last longer in our wire drawing process and can offer the same advantage to you.
	www.wiredie.com (143 words)

	WIRE-DRAWING-MACHINE TENDER - Job Description (Site not responding. Last check: 2007-11-04)
		Tends machines that weld ends of wire together to form continuous coil and draw wire through dies to reduce wire to specified diameter: Lifts reels of wire onto spindle of floor stand, manually, or using hoist.
		Threads wire around tension rollers, and through reducing dies, and fastens end of wire to spindle.
		Starts machine that draws wire through dies and around takeup reel.
	careerplanner.com /DOT-Job-Descriptions/WIRE-DRAWING-MACHINE-TENDER.cfm (118 words)

	Wire Nail Wire Drawing allied machineries,Wire Nail Wire Drawing allied machineries exporter,Wire Nail Wire Drawing ... (Site not responding. Last check: 2007-11-04)
		Pragati Industries has been a leading manufacturer and exporter of Wire Nail, Wire Drawing and allied machineries for wire industries in India for last 30 years.
		We are known for highly reliable, high-speed, low maintenance, easy to operate wire nail and wire drawing machines as well as ancillary machineries for wire industries.
		Moreover, we are also capable of manufacturing any other type of machinery which may be required by wire industries.
	www.exportersindia.net /exporters-manufacturers/pragatiindustries.htm (233 words)

	CSTEC: Wire Drawing (Site not responding. Last check: 2007-11-04)
		The purpose of the course on Wire Drawing is to prepare the learners to assume the duties of a wire drawing machine operator in a supervised production environment.
		This course is to be complemented by a supervised training period of about X weeks long (to be determined) to reach a degree of proficiency in the duties and operations that will guarantee complete autonomy.
		To describe the operation of the computerized wire drawing machine control process.
	www.cstec.ca /wire_course.html (717 words)

	Tungsten Carbide Wire Drawing Dies Manufacturers (Site not responding. Last check: 2007-11-04)
		PRATAP ENTERPRISES - Mfrs of Tungsten Carbide Wire Drawing Dies in all
		Pratap Enterprises: Mfrs of Tungsten Carbide Wire Drawing Dies in all
		Manufacturers of tungsten carbide wire drawing dies and associated products including rolls spinner, shaving, shaped dies, press tools, plastic mold tools cutter dies twisting dies drive...
	www.mypalmplace.com /directory/Tungsten-Carbide-wire-drawing-dies-manufacturers.html (843 words)

	DMOZ : Business : Industrial Goods and Services : Cable and Wire : Tools and Equipment : Wire Drawing (Site not responding. Last check: 2007-11-04)
		Suppliers of all types of wire drawing equipment and accessories used in making alloy steels, carbon steels.
		Resizing and Polishing service of diamond draw and carbide draw dies.
		Manufacturers of tungsten carbide wire drawing dies and associated products including rolls spinner, shaving, shaped dies, press tools, plastic mold tools cutter dies twisting dies drive rolls chain dies clutch dies
	www.dmoz.x-sms.pl /Business/Industrial_Goods_and_Services/Cable_and_Wire/Tools_and_Equipment/Wire_Drawing (316 words)

	Items for wire-drawing (Site not responding. Last check: 2007-11-04)
		Accuracy requirement of size, high quality of a surface and high mechanical properties of an outstretched material, minimal power consumption, high resistance of a tool, high efectiveness of equipment and low metal waste while drawing, low drawing production value: wires, bars, pipes are accomplished with properties and geometric properties of drawing tools.
		This drawing tool which is modern, effective, profitable is dies made of hard alloys.
		Dies with billets made of hard alloys dozen times and sometimes hundred times are more stable than steel dies, and several times cheaper than diamond dies.Wire, bars and pipes made of ferrous and non-ferrous metals and their alloys can be successfully and efficialntly stretched into these dies.
	www.kzts.ru:8101 /eng/p_2_1.html (224 words)

	Environment Agency - Drawing of Wire (Site not responding. Last check: 2007-11-04)
		These guidelines are relevant to businesses cold drawing wire from coiled rod through dies.
		For the purpose of these guidelines, it is assumed that wire drawing is performed as a continuous operation using draw blocks.
		Lubricants are used in drawing processes that also act as coolants, thermal barriers and corrosion inhibitors.
	www.environment-agency.gov.uk /netregs/sectors/438536/438561?lang=_e (160 words)

Try your search on: Qwika (all wikis)